Changing the battery in a Timex watch is a relatively simple task that can be completed in a few minutes with a few simple tools. However, it is important to take care not to damage the watch or the battery during the process. The following step-by-step guide will walk you through the process of changing a Timex battery safely and easily.
Before you begin, you will need to gather a few tools. These include a small Phillips head screwdriver, a pair of tweezers, and a new watch battery. It is also helpful to have a clean cloth or paper towel to place the watch on while you are working. Once you have gathered your tools, you are ready to begin.
The first step is to remove the back of the watch. To do this, use the Phillips head screwdriver to unscrew the four small screws that are located around the perimeter of the back of the watch. Once the screws are removed, carefully pry the back of the watch off. Be careful not to damage the gasket that is located around the edge of the back of the watch. This gasket helps to keep water out of the watch, so it is important to make sure that it is not damaged.
Identifying the Battery Compartment
Locate the battery compartment, usually found on the back of the Timex watch. It is typically secured by a small screw or a snap-on cover. Note that the battery compartment may vary in appearance depending on the specific Timex model you have.
**Here’s a detailed guide to identifying different battery compartment types:**
| Compartment Type | Description |
|---|---|
| Screwed-in Compartment | Features a small screw that holds the cover in place. You’ll need a small screwdriver to remove the screw. |
| Snap-On Compartment | Has a snap-on cover that can be easily lifted off by applying gentle pressure on the sides. |
| Hidden Compartment | Integrated into the watch’s design, often concealed behind a small tab or lever. Requires more delicate handling to access. |
Once you’ve identified the battery compartment, proceed to the next step to open it and replace the battery.
Removing the Back Case
Replacing the battery in your Timex watch requires removing the back case. This can be done easily with the right tools and a bit of care. Here’s a step-by-step guide:
1. Gather your tools: You will need a small Phillips head screwdriver and a case knife or putty knife.
2. Secure your watch: Place your watch on a soft surface to prevent scratches or damage. Use a watch repair clamp or a piece of tape to hold the watch securely.
3. Remove the screws: Using the Phillips head screwdriver, carefully remove the screws that hold the back case in place. These screws are usually located around the perimeter of the back case.
4. Pry open the back case: Once the screws are removed, insert the case knife or putty knife into a small gap between the back case and the watch body. Gently pry the back case upward to separate it from the watch body.
5. Note the position of the gasket: As you remove the back case, pay attention to the position of the gasket that seals the back case to the watch body. This gasket is important for maintaining water resistance, so it should not be damaged or displaced.
6. Remove the old battery: Once the back case is open, you will see the old battery. Use a pair of tweezers or your fingers to carefully remove the battery from its compartment. Be careful not to touch the battery terminals, as this could damage the watch.
Securing the Watch Face
1. Locate the Watch Battery Cover
The watch battery cover is typically a small, round metal disk on the back of the watch. It may have a small notch or indentation that allows you to pry it open with a small screwdriver or knife.
2. Carefully Pry Open the Cover
Insert the screwdriver or knife into the notch and gently pry up on the cover. Avoid using too much force, as you could damage the watch.
3. Remove the Old Battery
Once the cover is open, you will see the old battery. It is usually held in place by a small spring or clip. Gently push or lift on the battery to remove it.
Tips for Removing the Old Battery
- Avoid touching the battery with your bare hands, as the oils on your skin can damage it.
- If the battery is stuck, use a pair of needle-nose pliers to gently pry it loose.
- Be careful not to drop the battery, as it can be dangerous if swallowed.
| Battery Type | Voltage | Diameter (mm) | Height (mm) |
|---|---|---|---|
| CR2016 | 3V | 20 | 1.6 |
| CR2025 | 3V | 25 | 1.6 |
| CR2032 | 3V | 32 | 3.2 |
Lifting the Battery
Now, it’s time to extract the depleted battery from its housing. To do this, perform these careful steps:
1. Locate the battery clamp: Examine the battery compartment’s interior thoroughly. You should find a small, spring-loaded clamp holding the battery in place.
2. Press down on the clamp: Using a non-metallic tool like a toothpick or plastic tweezers, gently press down on the battery clamp’s center.
3. Lift the clamp: As you maintain pressure on the clamp, use the tool’s tip to gently lift one end of the clamp away from the battery.
4. Slide the battery out: Once one end of the clamp is lifted, carefully slide the battery towards the opening. Grip the battery’s edge with your fingers or tweezers and remove it completely from the compartment.
| Battery Size | Estimated Time to Deplete |
|---|---|
| 377 | 2 years |
| SR621SW | 3 years |
| 394 | 5 years |
| CR2016 | 7 years |
Installing the New Battery
1. Turn the watch over and locate the small screw on the back. Use a small screwdriver to carefully unscrew it.
2. Once the screw is removed, gently pry open the back of the watch using a thin tool (such as a toothpick or a plastic spudger).
3. Locate the battery inside the watch. It will typically be held in place by a small metal clip or bracket.
4. Use tweezers to carefully remove the old battery from the clip. Note the orientation of the battery so that you can insert the new battery in the correct direction.
5. Take the new battery and place it into the clip, making sure that the positive (+) side of the battery is facing the same direction as the positive (+) terminal on the watch. To ensure a secure connection, press down firmly on the battery until it clicks into place.
| Battery Size | Timex Watch Models |
|---|---|
| SR626SW | Expedition, Ironman, Timex Weekender |
| CR2025 | Weekender Chronograph, Expedition Chronograph |
| CR2016 | Easy Reader, Classic Timex |
6. Replace the back of the watch and tighten the screw.
Positioning the Case Back
Once the battery is removed, it’s time to replace the case back. This process is generally straightforward, but there are a few things to keep in mind to ensure a proper fit and avoid damage to the watch.
Key Tips:
1. Align the Notch: The case back typically has a small notch or cutout that aligns with a corresponding marking on the watch case. Make sure to align these markings to ensure proper fit.
2. Use Light Pressure: Press the case back firmly into place, but avoid applying excessive force. Start by pressing gently around the edges and progressively apply more pressure until the case back is fully seated.
3. Check the Fit: Once the case back is in place, check to ensure it is secured by gently twisting or pulling on it. There should be no movement or gaps between the case back and the watch case.
4. Avoid Scratches: Be careful not to scratch the watch case or the case back during the process. Use a cloth or soft material to protect the watch if necessary.
5. Tighten Screws (if Applicable): Some Timex watches may have screws that secure the case back. If present, tighten these screws gently but securely using a suitable tool.
6. Advanced Tips for Tightening the Case Back: For additional security and water resistance, consider using a watchmaker’s press or a dedicated case back tool. These tools apply controlled pressure to ensure a tight and watertight seal. Additionally, applying a small amount of silicone lubricant around the gasket on the case back can improve the seal and prevent future leaks.
Setting the Time and Date
Once the new battery is installed, you can now set the time and date on your Timex watch. Here are the steps:
1. Pull the Crown Out to Position 2
Locate the crown on the side of the watch and pull it out to position 2 (one click out). The second hand will stop moving, indicating that the watch is in setting mode.
2. Rotate the Crown to Set the Hour
Rotate the crown clockwise to move the hour hand forward by one hour at a time. Counterclockwise to move it backward.
3. Pull the Crown Out to Position 3
Once the hour is set, pull the crown out to position 3 (two clicks out). The minute hand will now start moving.
4. Rotate the Crown to Set the Minute
Rotate the crown clockwise to move the minute hand forward by one minute at a time. Counterclockwise to move it backward.
5. Push the Crown Back In to Position 2
Once the minutes are set, push the crown back in to position 2 (one click out). The second hand will begin moving again.
6. Set the Date
To set the date, press the top button on the watch. This will advance the date by one day at a time.
7. Pull the Crown Out to Position 1
Once the date is set, pull the crown out to position 1 (one click out) to stop the second hand.
8. Hold the Bottom Button for 5 Seconds
Hold the bottom button on the watch for 5 seconds. This will reset the second hand to the 12 o’clock position. Release the button.
9. Push the Crown Back In
Push the crown back in to position 1 to engage the watch.
Verifying Battery Function
To verify if the battery in your Timex watch needs to be replaced, follow these steps:
1. Check for Dim or Inaccurate Timekeeping: A dim display or inaccurate timekeeping can indicate a weak battery.
2. Monitor the Second Hand: A second hand that jumps or stops momentarily may signify a low battery.
3. Reset the Watch: If the timekeeping is significantly off, you can try resetting the watch by pressing and holding the reset button for 5-10 seconds.
4. Use a Battery Tester: You can use a battery tester to measure the voltage of the battery. A voltage reading below 1.25V typically indicates a weak or dead battery.
5. Observe the Battery Compartment: Look for any visible corrosion or leakage from the battery compartment.
6. Listen for a Ticking Sound: Hold the watch near your ear and listen for a faint ticking sound. A lack of ticking may suggest a dead battery.
7. Test the Watch in Different Positions: Rotate the watch in different positions to check if the display becomes brighter or the timekeeping improves. This may indicate a loose battery connection.
8. Check the Watch’s Specifications: Refer to the watch’s manual or specifications to determine the recommended battery type and lifespan.
9. Troubleshooting Common Battery-Related Issues:
Troubleshooting
If you are having trouble changing the battery in your Timex watch, here are a few troubleshooting tips:
1. Make sure you have the right battery.
The correct battery for your Timex watch will be listed in the user manual. If you don’t have the user manual, you can usually find the battery type by looking at the back of the watch.
2. Make sure the battery is properly installed.
The battery should be placed in the watch with the positive (+) side facing up. If the battery is installed incorrectly, it will not power the watch.
3. Make sure the watch is properly closed.
Once the battery is installed, you need to make sure the watch is properly closed. If the watch is not closed properly, it will not be water-resistant.
4. If you are still having trouble, you can contact Timex customer service.
Timex customer service can be reached by phone at 1-800-448-4639 or by email at [email protected]
How to Change a Timex Battery
Changing a Timex battery is a simple process that can be completed in a few minutes. Here are the steps to do it:
- Gather your materials. You will need a new Timex battery, a small Phillips head screwdriver, and a pair of tweezers.
- Open the back of the watch. To do this, use the screwdriver to unscrew the four screws that hold the back in place.
- Remove the old battery. Use the tweezers to gently lift the old battery out of the watch.
- Insert the new battery. Make sure that the positive (+) side of the battery is facing up.
- Close the back of the watch. Screw the four screws back into place.
- Set the time and date. Use the watch’s controls to set the correct time and date.
People Also Ask About How To Change A Timex Battery
How often should I change my Timex battery?
Most Timex batteries will last for about two years. However, if you notice that your watch is losing time or the second hand is skipping, it may be time to change the battery.
What type of battery does a Timex watch use?
Timex watches use a variety of different battery types. The type of battery that your watch uses will be listed on the back of the watch.
Can I change the battery in my Timex watch myself?
Yes, you can change the battery in your Timex watch yourself. However, if you are not comfortable doing this, you can take your watch to a jeweler or watch repair shop.
