Imagine trying to access your home, but the code you’ve been using for years no longer works. It’s a frustrating and potentially stressful situation. But don’t worry; changing the code on a Schlage lock is a relatively simple process that can be completed in just a few steps. In this article, we’ll provide you with clear instructions on how to change the code on your Schlage lock. Whether you’re a homeowner or a renter, knowing how to change the code is an essential part of home security.

Before we dive into the steps, it’s worth noting that Schlage offers various lock models, each with slightly different features and coding mechanisms. However, the general principles remain the same. To begin, gather the necessary tools: the programming tool (usually a small, plastic card or key), the new code you want to use, and a pen or pencil to take notes. Once you have everything you need, find a clear and well-lit workspace where you can focus on the task at hand.

Now, let’s get started with the step-by-step guide to changing the code on your Schlage lock. The first step is to remove the interior cover plate by unscrewing the screws or using a release latch. Once the cover plate is removed, you’ll see the lock’s interior mechanism. Locate the programming button, which is usually a small, recessed button. Using the programming tool, press and hold the programming button for a few seconds until you hear a beep or see a light flash. This indicates that the lock is now in programming mode.

Gather Necessary Materials

Before you begin the process of changing the Schlage code, it is crucial to ensure that you have all the necessary materials at hand. This will save you time and minimize the risk of errors. Here’s a detailed list of what you will need:

Material	Purpose
Schlage lock with existing code	The lock you wish to change the code on
Phillips-head screwdriver	For removing the faceplate of the lock
Small flat-head screwdriver or paperclip	For pressing the reset button
New Schlage code (4-8 digits)	The new access code you want to set

Locate the Programming Button

Locating the programming button on a Schlage lock is crucial for changing the access code. Here is a step-by-step guide with additional details to help you find it:

1. Open the battery cover: Locate the small, round battery cover on the back of the lock’s keypad. Use a screwdriver or coin to carefully pry it open.

2. Remove the lock: Gently pull the entire lock assembly away from the door. The lock will be connected to the door by wires; disconnect them by pressing the small tabs or levers on the connectors.

3. Identify the programming button: Once the lock is detached, you’ll see a small, recessed button on the back of the lock’s housing. This button is usually hidden behind a small rubber flap or cover. Carefully lift the flap or cover to expose the programming button.

Enter Current User Code

Now, enter the current user code to unlock the keypad.
Ensure that the user code used is from an authorized user.
After entering the user code, the keypad should beep once, indicating successful entry.

If there are multiple authorized users, be sure to select the correct user code.
Without the correct user code, you will not be able to proceed with changing the lock code.

Create a New Code

To create a new code, you will need to access the Schlage Encode Smart WiFi Deadbolt’s programming menu. To do this:

Enter your current master code on the keypad.
Press the Schlage button on the bottom of the keypad.
Press the “4” button on the keypad.
Enter the new code you want to create (4-8 digits).
Press the Schlage button again to save the new code.

You can create up to 30 user codes in addition to the master code. User codes can be 4-8 digits long and can be used to unlock the door using the keypad.

Here is a table summarizing the steps for creating a new code:

Lock Model	Programming Button Location
Schlage Encode Plus	Inside the battery compartment, next to the battery terminals
Schlage Connect	Behind a rubber flap on the back of the lock’s housing
Schlage BE365	Inside the battery compartment, under the battery cover

Step	Action
1	Enter your current master code on the keypad.
2	Press the Schlage button on the bottom of the keypad.
3	Press the “4” button on the keypad.
4	Enter the new code you want to create (4-8 digits).
5	Press the Schlage button again to save the new code.

Replace the Battery Cover

Locate the battery cover on the back of the lock. It is typically held in place by a screw or two. Remove the screws and set them aside. Carefully remove the battery cover and set it aside as well.

Step 1: Disconnect the Battery

Once the battery cover is removed, disconnect the battery from the lock. This is typically done by pressing on a tab or lever and pulling the battery out.

Step 2: Inspect the Battery

Inspect the battery for any signs of damage or corrosion. If the battery is damaged, it will need to be replaced. If the battery is not damaged, it can be reused.

Step 3: Replace the Battery

If the battery needs to be replaced, insert a new battery into the lock. The positive terminal of the battery should face the positive terminal on the lock. Press the battery into place until it clicks.

Step 4: Reconnect the Battery

Reconnect the battery to the lock by pressing it back into place until it clicks. Make sure that the battery is securely connected.

Step 5: Replace the Battery Cover

Replace the battery cover over the battery and secure it with the screws. Make sure that the battery cover is securely attached.

Step 6: Test the Lock

Test the lock by entering your code. If the lock does not unlock, double-check your code and make sure that the battery is properly connected. If the lock still does not unlock, you may need to contact a locksmith.

Test the New Code

Once you have changed the code, it is important to test it to make sure that it works properly. To do this, simply enter the new code into the keypad and press the “Enter” button. If the door unlocks, then the code has been successfully changed.

However, if the door does not unlock, then there may be a problem with the code. In this case, you should try the following steps:

Make sure that you are entering the correct code.
Check the keypad to make sure that it is working properly.
Reset the lock to its factory settings and then try again.

If you are still having problems, you should contact Schlage customer service for assistance.

Here is a table summarizing the steps for testing the new code:

Step	Action
1	Enter the new code into the keypad.
2	Press the “Enter” button.
3	If the door unlocks, the code has been successfully changed.
4	If the door does not unlock, try the troubleshooting steps above.

Program Additional Codes (Optional)

You can program up to 19 additional user codes. To do this:

1. Press the “Schlage” button on the keypad.
2. Enter your master code.
3. Press the “#” key.
4. Enter a new 4- to 8-digit user code.
5. Press the “#” key.
6. Repeat steps 4-5 for each additional user code you want to program.
7. Press the “Schlage” button to save your changes.

Reset All User Codes

To reset all user codes to the factory default of “1234”:

1. Press the “Schlage” button on the keypad.
2. Enter your master code.
3. Press and hold the “#” key for 5 seconds.
4. All user codes will be reset to “1234”.

How To Change A Schlage Code

Reset Lock to Factory Settings (Optional)

If you’re experiencing problems with your Schlage lock, resetting it may help solve the issue. Here’s how to do it:

Remove the battery cover from the back of the lock.
Remove the battery.
Press and hold the reset button for 10 seconds.
Reinsert the battery and replace the battery cover.
Your lock is now reset to factory settings.

Change Code

To change the door code, follow these steps:

Enter your current code to unlock the door.
Press the Schlage button.
Enter the new code (6-19 digits).
Press the Schlage button again to confirm.
Your code has now been changed.

Add User Codes (Optional)

You can add up to 19 user codes to your Schlage lock. Here’s how:

Enter your master code.
Press the Schlage button.
Enter the new user code.
Press the Schlage button again.
Repeat steps 3-4 for each additional user code you want to add.

Delete User Codes (Optional)

To delete a user code, follow these steps:

Enter your master code.
Press the Schlage button.
Enter the user code you want to delete.
Press the Schlage button again.
The user code has now been deleted.

Program Lock to Auto-Lock (Optional)

To program your lock to auto-lock, follow these steps:

Enter your master code.
Press the Schlage button.
Enter the number “1” followed by the Schlage button.
Enter the desired auto-lock time (5-99 seconds) followed by the Schlage button.
Your lock is now programmed to auto-lock.

Disable Auto-Lock (Optional)

To disable auto-lock, follow these steps:

Enter your master code.
Press the Schlage button.
Enter the number “0” followed by the Schlage button.
Your lock is now programmed to auto-lock.

Change Master Code

To change the master code, follow these steps:

Enter your current master code.
Press the Schlage button.
Enter the number “9” followed by the Schlage button.
Enter the new master code followed by the Schlage button.
Your master code has now been changed.

Lock Out All User Codes (Optional)

To lock out all user codes, follow these steps:

Enter your master code.
Press the Schlage button.
Enter the number “7” followed by the Schlage button.
All user codes have now been locked out.

Restore Access to Locked Out User Codes (Optional)

To restore access to locked out user codes, follow these steps:

Enter your master code.
Press the Schlage button.
Enter the number “8” followed by the Schlage button.
All user codes have now been restored.