The useful strings in the hood of a sweatshirt have inadvertently become detached. You want to fix it and make it as good as new but don’t know how to put the drawstring back in the hoodie. Here I will describe how to rethread a hoodie drawstring in four simple steps. Grab a pair of scissors, a safety pin, and your hoodie, and let’s get started.
Begin by locating the small hole on either side of the hood opening. These openings are where the drawstring will enter the hood. Next, tie one end of the drawstring to the safety pin, ensuring the knot is secure. From there, insert the safety pin into the hole and pull the attached drawstring through until the knot catches against the fabric. Repeat these steps for the other side of the hood.
Once both ends of the drawstring are threaded through the holes, pull the drawstring to the desired length. Secure the ends by tying knots close to the tips. These knots will prevent the drawstring from slipping out through the holes. As a final touch, trim any excess string, and your rethreaded hoodie is complete. Enjoy the convenience of a fully functional hoodie once again with a properly threaded drawstring.
Removing the Old Drawstring
To successfully remove the old drawstring from your hoodie, follow these detailed steps:
1. Locate the Drawstring Casing
Inspect the inside of your hoodie to identify the drawstring casing. It is a narrow channel or tunnel that runs along the hood’s edge and contains the drawstring. Usually, it appears as a folded fabric loop stitched along the seam of the hood.
2. Find the Drawstring Access Point
Along the drawstring casing, look for a small opening or hole that allows access to the drawstring. It may be located near one of the hood’s grommets or eyelets. If you cannot locate the access point, gently pull on the drawstring ends to see if they emerge from a specific spot.
3. Extract the Drawstring
Once you have located the access point, gently pull one end of the drawstring outward. The other end should follow suit, allowing you to remove the entire drawstring from the casing. Be careful not to pull too forcefully, as this could damage the casing or the drawstring itself.
4. Check for Additional Attachment Points
In some cases, the drawstring may be secured by additional stitching or knots at specific points along the casing. If you encounter any resistance while pulling, check for these attachment points and carefully remove them using a seam ripper or scissors. Once all attachment points are released, you should be able to remove the drawstring completely.
Table: Summary of Drawstring Removal Steps
| Step | Description |
|---|---|
| 1 | Locate the drawstring casing. |
| 2 | Find the drawstring access point. |
| 3 | Extract the drawstring. |
| 4 | Check for additional attachment points. |
Preparing the New Drawstring
1. Measure the Length
Determine the appropriate length for the new drawstring by measuring the existing one that was removed. You want the new one to be similar in length to facilitate an effortless fit through the hood’s casing.
2. Choose the Material
Drawstrings come in various materials, including cotton, polyester, and nylon. Cotton is a natural and comfortable choice, while polyester and nylon are durable and moisture-resistant. Consider the desired aesthetic and functionality when selecting the material.
3. Enhance Durability with Aglet or Tips
To prevent the ends of the drawstring from fraying or unraveling, use an aglet or tips. Aglet refers to the small plastic or metal caps that can be threaded onto the cord ends. Tips are heat-sealed caps that provide a professional finish and added strength. Follow the steps carefully to ensure a secure attachment:
a) Threading an Aglet
* Fold over the cord end by approximately 1.5 centimeters.
* Insert the folded end into the aglet and pull the cord through.
* Gently squeeze the aglet with pliers to secure the cord.
b) Applying Heat-Sealed Tips
* Firmly grip the cord end using a small cloth or pliers.
* Heat a lighter or candle and carefully hold the flame 1-2 centimeters away from the cord end.
* Rotate the cord slightly as you heat the end to evenly melt the fibers.
* Remove the flame once the end becomes rounded and sealed.
Inserting the Drawstring into the Channels
Once you have prepared the drawstring and the hoodie, it’s time to insert the drawstring into the channels. This process requires precision and care to ensure the drawstring runs smoothly through the channels.
Step 1: Locate the entrance of the channel on the inside of the hood. The entrance is typically a small hole or opening.
Step 2: Insert the end of the drawstring into the entrance of the channel. Use a safety pin or needle to guide the drawstring through the channel if it’s too narrow.
Step 3: Gently guide the drawstring through the channel using a long object like a knitting needle or chopstick. The object should be smooth and slightly flexible to avoid damaging the fabric.
Step 4: Repeat step 3 for the other side of the channel. Once the drawstring is fully inserted through both channels, proceed to the next step.
| Step | Description |
|---|---|
| 1 | Locate the entrance of the channel |
| 2 | Insert the end of the drawstring into the channel |
| 3 | Guide the drawstring through the channel with an object |
| 4 | Repeat step 3 until the drawstring is fully inserted through both channels |
Tying the Drawstring Knots
The final step in replacing the drawstring is to tie the knots that will secure it in place. This process is relatively simple, but there are a few nuances to keep in mind to ensure that the knots are secure and the drawstring is functional.
1. Gather the Ends of the Drawstring
Bring the two ends of the drawstring together and align them so that they are parallel to each other.
2. Tie the Square Knot
Cross the right-hand end of the drawstring over the left-hand end and bring it around the back. Now, cross the left-hand end over the right-hand end and bring it around the back. Pull both ends of the drawstring tightly to form a square knot.
3. Adjust the Knot
Slide the knot down the drawstring to the desired position. Make sure that the knot is securely tied and that the drawstring is not slipping.
4. Repeat Step 2
Repeat steps 2-3 to tie the second knot. This time, start with the left-hand end of the drawstring and cross it over the right-hand end. The final result should be two secure square knots that hold the drawstring in place.
5. Finishing Touches
Trim any excess drawstring that extends beyond the knots. You can also use a lighter to melt the ends of the drawstring to prevent them from fraying. This will create a clean and professional-looking finish.
| Type of Knot | Description |
|---|---|
| Square Knot | The standard knot for securing drawstrings. It is easy to tie and provides a secure hold. |
Concealing the Knots
To keep your drawstring secure and discreet, here’s a step-by-step guide to concealing the knots:
Step 1: Pull the Drawstring Through
Insert the safety pin or bodkin into the hole at the end of the drawstring channel. Push it through the channel until it exits out the other end.
Wrap the spare end of the drawstring around the safety pin or bodkin, then pull the safety pin or bodkin back through the channel, bringing the drawstring with it.
Step 2: Make Two Knots
Tie two overhand knots in the ends of the drawstring. Pull the knots tightly to secure them.
Step 3: Position the Knots
Slide the knots back into the drawstring channel, ensuring they are close to the hoodie’s hem.
Step 4: Close the Channel
Use the needle and thread or sewing machine to stitch the ends of the drawstring channel closed. Reinforce the stitches for durability.
Step 5: Check the Drawstring
Pull on the drawstring to verify that it is functional and secure. The knots should not be visible or impede the drawstring’s movement.
Step 6: Clean Up
Trim any excess thread and remove the safety pin or bodkin. Your drawstring is now securely concealed.
Step 7: Alternative Method
If the above method is too complex, you can use a small piece of heat-shrink tubing. Slide the tubing over the knots and use a heat gun or hairdryer to shrink the tubing, securing the knots and concealing them within the drawstring channel.
Finishing the Repair
Once all of the drawstring is threaded back through the casing, you can finish the repair by tying the ends of the drawstring together. To do this, follow these steps:
- Pull the two ends of the drawstring tight so that the casing is snug around the cord.
- Tie the ends of the drawstring together using a double knot.
- Trim any excess drawstring.
If you’ve lost the aglets (the plastic or metal tips at the ends of the drawstring), you can replace them with small beads or knots. Simply thread the bead or knot onto the end of the drawstring and then tie a double knot to secure it.
Tips for Tying the Drawstring
Here are a few tips for tying the drawstring:
- Use a square knot, which is the most secure type of knot.
- Tie the knot close to the casing so that it doesn’t slip.
- Trim the excess drawstring to prevent it from fraying.
| Knot Type | Security | Ease of Tying |
|---|---|---|
| Square Knot | High | Medium |
| Bow Tie | Medium | Easy |
| Granny Knot | Low | Easy |
Once you’ve tied the drawstring, your hoodie is repaired and ready to wear!
Tips for Success
1. Choose the Right Drawstring
The first step is to choose the right size and color of the drawstring. The diameter of the drawstring should be slightly larger than the holes in the hoodie, and the color should match or complement the color of the hoodie.
2. Fold the Drawstring
Once you’ve chosen the right drawstring, fold it in half. This will make it easier to thread through the holes.
3. Thread the Drawstring
Use a safety pin or needle to thread the drawstring through the holes in the hoodie. Start at the bottom of the hoodie and work your way up.
4. Tie the Ends
Once you’ve threaded the drawstring through all the holes, tie the ends together. Make sure the knot is secure.
5. Adjust the Drawstring
Pull on the ends of the drawstring to tighten or loosen it. Adjust the drawstring so that it fits comfortably.
6. Conceal the Knot
Once you’ve adjusted the drawstring, conceal the knot by tucking it inside the hoodie.
7. Trim the Excess
If there’s any excess drawstring left, trim it off.
8. Use a Drawstring Needle
If you’re having trouble threading the drawstring, you can use a drawstring needle. A drawstring needle is a small, curved needle that makes it easy to thread the drawstring through the holes.
9. Troubleshooting
| Problem | Solution |
|---|---|
| The drawstring is too long. | Trim the excess drawstring off. |
| The drawstring is too short. | Splice two or more drawstrings together to make one longer one. |
| The drawstring is tangled. | Unfold the drawstring and carefully untangle it. |
| The drawstring is frayed. | Cut off the frayed part of the drawstring. |
Access at the Hood
Usually, you can easily find the hole for the drawstring at the hood of your hoodie. It’s commonly located near the seam where the hood attaches to the neckline. The hole may be hidden under a small flap of fabric or have a metal eyelet.
Unclogging the Drawstring Hole
If the drawstring hole is obstructed, you may need to use a small object to clear it. A safety pin, a bobby pin, or even a toothpick can be used to gently push any lint or debris out of the hole.
Threading the Drawstring
Once the hole is clear, thread the end of the drawstring through the hole. You may need to use a pair of tweezers or a needle to help you pull the drawstring through.
Adjusting the Length
Once the drawstring is threaded through the hole, adjust the length to your desired fit. You can simply pull on the ends of the drawstring to tighten it, or loosen it by pulling on the drawstring from the inside of the hoodie.
Tying a Knot or Installing an Aglet
To secure the drawstring in place, you can either knot the ends together or install a plastic or metal aglet. An aglet is a small, decorative tip that prevents the ends of the drawstring from fraying and makes it easier to adjust the drawstring.
Troubleshooting Common Issues
1. Drawstring is too short
If the drawstring is too short, you can try to extend it by tying a knot or attaching a piece of fabric or cord to the ends. However, it’s important to make sure that the drawstring is not too long, as this can be a safety hazard.
2. Drawstring is frayed or damaged
If the drawstring is frayed or damaged, you can replace it with a new one. You can find replacement drawstrings at most fabric stores or online retailers.
3. Hole for drawstring is ripped or torn
If the hole for the drawstring is ripped or torn, you can try to repair it using a sewing machine or by hand-stitching the hole closed. You can also use a fabric glue to secure the edges of the hole.
4. Drawstring keeps falling out
If the drawstring keeps falling out, you can try to secure it in place by tying a knot at the ends. You can also install a cord lock or a metal eyelet to keep the drawstring in place.
5. Drawstring is stuck inside the hoodie
If the drawstring is stuck inside the hoodie, you can try to pull it out gently. If the drawstring is still stuck, you may need to cut it out and replace it with a new one.
6. Drawstring is too tight or too loose
If the drawstring is too tight, you can loosen it by pulling on the drawstring from the inside of the hoodie. If the drawstring is too loose, you can tighten it by pulling on the ends of the drawstring.
7. Drawstring is not centered
If the drawstring is not centered, you can try to adjust it by pulling on the drawstring from either side. You can also try to re-thread the drawstring through the hole to make sure it is centered.
8. Drawstring is too slippery
If the drawstring is too slippery, you can try to roughen it up by rubbing it against a piece of sandpaper or a pair of scissors. You can also try to apply a small amount of wax to the drawstring to make it less slippery.
9. Drawstring is too stiff
If the drawstring is too stiff, you can try to soften it by soaking it in warm water for a few minutes. You can also try to apply a small amount of oil to the drawstring to make it more flexible.
10. Drawstring is fraying or unraveling
If the drawstring is fraying or unraveling, you can try to seal the ends with a small amount of clear nail polish or fabric glue. You can also try to wrap the ends of the drawstring with a piece of electrical tape to prevent it from fraying further.
How to Rethread a Drawstring in a Hoodie
A hoodie is a comfortable piece of clothing that can be worn in a variety of settings. One of the most important features of a hoodie is the drawstring, which allows you to adjust the hood to fit snugly around your head. Unfortunately, the drawstring can sometimes come out of the hoodie, which can be frustrating. However, it is a relatively easy fix to put the drawstring back in.
To rethread a drawstring in a hoodie, you will need a safety pin or a large needle. First, find the opening in the hood where the drawstring is supposed to come out. Next, insert the safety pin or needle into the opening and thread it through the hoodie until it comes out the other side.
Once the safety pin or needle is through the hoodie, tie the drawstring to the end of it. Then, pull the safety pin or needle back through the hoodie, pulling the drawstring with it. Finally, tie the drawstring around the neck of the hoodie to secure it.
People Also Ask
Can you put a drawstring back in a hoodie?
Yes, it is relatively easy to put a drawstring back in a hoodie. You will need a safety pin or a large needle.
How do you fix a drawstring in a hoodie?
To fix a drawstring in a hoodie, you will need to rethread it. You can do this by following the steps outlined above.
Where can you get a drawstring for a hoodie?
You can purchase a drawstring for a hoodie at most fabric stores or online retailers.
