Have you ever locked yourself out of your house because you forgot your Schlage door code? Or, perhaps you’ve moved into a new home and need to change the code from the previous owners. Resetting the code on your Schlage lock is a simple process that only takes a few minutes. In this comprehensive guide, we will walk you through the step-by-step process of resetting your Schlage door code, ensuring that you regain access to your home and enhance its security.
Before you begin the reset process, gather the necessary tools. You will need a screwdriver to remove the faceplate of the lock and access the programming button. Additionally, it’s essential to have a pen and paper handy to note down the new code you intend to set. Once you have assembled the necessary materials, follow the instructions outlined in the subsequent sections to successfully reset your Schlage door code.
Now that you have gathered the required tools, you can proceed with the reset process. Begin by removing the faceplate of your Schlage lock using the screwdriver. Locate the programming button, typically situated on the interior side of the lock, and press it once. The lock will emit a beep, indicating that it has entered programming mode. Next, enter the new code you wish to set, followed by the ‘#’ key. The lock will beep again to confirm the new code has been successfully programmed. Finally, reattach the faceplate and test the new code to ensure it works correctly. By following these steps diligently, you have successfully reset your Schlage door code, providing you with peace of mind and enhanced security for your home.
Identifying Your Lock Model
Understanding your Schlage door lock model is crucial before attempting a reset. Here are the steps to identify your lock model:
1. Inspect the Lock’s Front Panel
Locate the front panel of your Schlage lock where the keypad is situated. Examine the panel for any visible markings or labels that indicate the model name or number. The model number may be printed directly on the panel or engraved discreetly.
If the model number is not visible on the front panel, you can refer to the user manual or packaging that came with the lock. The user manual typically contains a section dedicated to identifying the lock model.
Alternatively, you can reach out to Schlage customer support for assistance in identifying your lock model. They can provide you with the necessary information based on the lock’s physical characteristics or serial number.
| Model Number | Series |
|---|---|
| FE285 | Connect |
| BE365 | Encode |
| F10-BEV | Keypad |
Gather Necessary Tools
To reset your Schlage door code, you’ll need the following tools:
- A small screwdriver or Allen wrench
- A pen or pencil
- A new Schlage door code (optional)
Remove the Faceplate
To begin, locate the small screw or Allen screw on the faceplate of your Schlage lock. Using the appropriate screwdriver or Allen wrench, carefully remove the screw and set it aside.
Once the screw is removed, gently pull the faceplate away from the lock. Be careful not to pull too hard, as the wires connecting the faceplate to the lock are still attached.
Locate the Reset Button
With the faceplate removed, you’ll see a small black button on the inside of the lock. This is the reset button. To reset the door code, simply press and hold the reset button for about 10 seconds.
You’ll know the reset is complete when you hear a beep and the lock flashes its lights.
Enter a New Door Code (Optional)
If you want to enter a new door code, you can do so after the reset is complete. Simply follow these steps:
- Press the “1” button on the lock.
- Enter your new door code (between 4 and 8 digits).
- Press the “Enter” button to save your new door code.
You can now reattach the faceplate to the lock and test your new door code.
Locate the Reset Button
Locating the reset button on your Schlage door lock is crucial to successfully resetting the door code. The reset button’s location varies depending on the model you have, but it’s typically hidden for security reasons. Here’s how to find the reset button on different Schlage door lock models:
Schlage Keypad Deadbolts (FE Series)
For Schlage FE series keypads, the reset button is located in a concealed position.
To access it:
-
Remove the battery cover.
-
Slide the battery holder down.
-
Push the reset button hidden beneath the battery holder.
Schlage Keypad Handlesets (F Series)
F series handlesets have a slightly different reset button location. Here’s how to find it:
-
Remove the trim plate from the interior side of the handle.
-
Locate the reset button next to the battery compartment.
-
Press the button to initiate the reset process.
Schlage Connect Smart Locks (BE Series)
For Schlage BE series smart locks, the reset button is more readily accessible. It’s located on the back of the lock, underneath the battery cover.
-
Remove the battery cover.
-
Press and hold the reset button for 10 seconds.
-
The lock will chime and reset to factory default settings.
| Lock Model | Reset Button Location |
|---|---|
| FE Series | Hidden beneath battery holder |
| F Series | Next to battery compartment |
| BE Series | Back of lock, under battery cover |
Triggering the Reset
The reset process for Schlage door codes involves a series of precise actions. To initiate the reset, follow these steps carefully:
1. Identify the Reset Button
Locate the small, recessed reset button on the interior side of the lock. It is typically concealed by the battery cover.
2. Remove the Battery Cover
Use a flat-head screwdriver or your fingernail to gently pry open the battery cover. This will expose the reset button.
3. Hold Down the Reset Button
With the battery cover removed, press and hold down the reset button for approximately 10-15 seconds. You should hear a brief beep or see the lock’s lights flash, indicating that the reset has been initiated.
4. Release the Reset Button and Remove Batteries
After holding down the reset button for the specified time, release it. Immediately remove both batteries from the lock. Wait for a few minutes before proceeding to the next step.
| Time Pressed | Action |
|---|---|
| 10 Seconds | Resets user codes and settings |
| 20 Seconds | Resets master code and all settings |
Entering the Master Code
The Master Code is a unique code that is programmed into the lock by the manufacturer. It is used to access the lock’s programming mode, where you can change the user codes, the auto-lock settings, and other options. To enter the Master Code, follow these steps:
1.
Press the “Program” button on the keypad.
2.
Enter the Master Code. The default Master Code is “1234”.
3.
Press the “#” key.
4.
The lock will beep twice to indicate that you have entered the Master Code correctly.
5.
You are now in programming mode. You can now change the user codes, the auto-lock settings, and other options.
| Programming Option | Keypad Sequence |
|---|---|
| Change User Code | Enter the Master Code > * > Enter the user number (1-250) > # > Enter the new user code > # |
| Change Auto-Lock Setting | Enter the Master Code > * > 3 > # > Enter the new auto-lock setting (0-999 seconds) > # |
| Factory Reset | Enter the Master Code > * > 9 > # |
Setting a New User Code
To set a new user code for your Schlage door lock, follow these steps:
- Enter your existing master code.
- Press the Schlage button.
- Within 30 seconds, press the asterisk (*) key.
- Enter a new user code (2-8 digits).
- Press the pound (#) key.
- The Schlage lock will beep twice to indicate that the new user code has been successfully set.
Advanced User Code Settings
In addition to the basic steps above, you can also set advanced user code settings, such as:
-
Temporary codes: Set a code that expires after a specified period of time.
-
One-time codes: Set a code that can only be used once.
-
Scheduled codes: Set a code that is only valid during specific hours or days.
To access these advanced settings, follow these steps:
- Enter your existing master code.
- Press the Schlage button.
- Within 30 seconds, press the asterisk (*) key twice.
- Enter the advanced setting code (see table below).
- Follow the on-screen prompts to set the desired setting.
| Advanced Setting Code | Setting |
|---|---|
| 5 | Temporary codes |
| 6 | One-time codes |
| 7 | Scheduled codes |
Verifying the New Code
Once you’ve successfully reset your Schlage door code, it’s essential to verify if it works correctly. Follow these steps to confirm the new code:
Step 1: Attempt to Unlock
Enter the new code you just set into the keypad. If the door unlocks, you’ve successfully reset the code.
Step 2: Check for Errors
If the door does not unlock, check for any errors on the keypad. Make sure you’re inputting the correct code and that the keypad is responding correctly.
Step 3: Retry Entering the Code
If you’re confident the code is correct but the door still doesn’t unlock, try entering the code again. Sometimes, the keypad may not register the first attempt.
Step 4: Check the Keypad Battery
A low battery can affect keypad functionality. Check if the battery needs to be replaced. A weak battery can cause sporadic issues with code recognition.
Step 5: Contact Schlage Support
If you’ve tried all the steps above but still have issues with the new code, contact Schlage customer support for further assistance. They may have additional troubleshooting steps or provide guidance on resolving more complex issues.
Troubleshooting Reset Issues
Incorrect Code or Key
Verify that you are using the correct code or key to reset the lock. If you have multiple Schlage locks, ensure you are using the correct one.
Dead or Low Battery
A weak or dead battery can prevent the lock from resetting. Replace the batteries with fresh ones and try resetting again.
Jammed Mechanism
A jammed mechanism can also hinder the reset process. Try manually unlocking the lock with a key or gently tapping the keypad to dislodge any debris or obstructions.
Incorrect Reset Procedure
Double-check that you are following the correct reset procedure for your specific Schlage lock model. Refer to the user manual or the manufacturer’s website for guidance.
Component Failure
In some cases, a faulty component, such as the keypad or microcircuit, may prevent the lock from resetting. Contact Schlage customer support for further assistance.
Firmware Issues
Outdated or corrupted firmware can cause reset problems. Check the Schlage website for any available firmware updates and install them to resolve the issue.
Programming Limit Reached
Schlage locks have a programming limit, which determines the maximum number of times the code or key can be reprogrammed. If this limit has been reached, you will need to factory reset the lock to delete all existing codes and keys.
EEPROM Corruption
The EEPROM (Electronically Erasable Programmable Read-Only Memory) stores the lock’s configuration and codes. If the EEPROM becomes corrupted, it can cause the lock to malfunction and prevent it from resetting. In such cases, the lock may need to be serviced or replaced.
Resetting a Schlage Door Code
Follow these steps to reset the door code on your Schlage lock:
1. Enter the current door code to unlock the door.
2. Press and hold the “Programming” button for 3 seconds.
3. Enter the new door code (between 4 and 8 digits).
4. Press the “Programming” button again.
5. The lock will beep and the new door code will be set.
6. Test the new door code to make sure it works.
Additional Security Measures
In addition to resetting the door code, you can take the following steps to improve the security of your Schlage lock:
9. Use a strong door code
Your door code should be at least 6 digits long and should not be easy to guess. Avoid using common sequences like “1234” or “0000”. Instead, use a random combination of numbers and letters. The table shows how long it would take a thief to crack a code of different lengths.
| Code length | Time to crack |
|---|---|
| 4 digits | Less than an hour |
| 6 digits | About a day |
| 8 digits | About a year |
10. Change the door code regularly
Don’t keep the same door code for too long. Change it every few months or so to make it harder for thieves to guess.
11. Use the deadbolt
The deadbolt is the strongest part of your lock. Always engage the deadbolt when you leave your home, even if you’re just going out for a short time.
Considerations for Multiple Users
If you have multiple users with access to your Schlage door lock, you may need to reset the code for all users if you are unable to identify the specific user who needs their code reset. Here’s how to do it:
| Step | Action |
|---|---|
| 1 | Enter the current master code. |
| 2 | Press the “*” key. |
| 3 | Enter the new master code. |
| 4 | Press the “*” key. |
| 5 | Re-enter the new master code. |
| 6 | Press the “#” key. |
This will reset the master code and all user codes. You will need to reprogram each user’s code using the new master code.
How to Reset Schlage Door Code
It is important to reset your Schlage door code from time to time for security reasons. Resetting the code will prevent unauthorized access to your home. There are a few different ways to reset your code, depending on the model of Schlage door lock you have.
For Schlage Connect Smart Locks
- Open the Schlage Home app on your smartphone and tap on the lock you want to reset.
- Tap on the “Settings” icon in the top right corner of the screen.
- Scroll down and tap on “Reset Code”.
- Follow the instructions on the screen to reset your code.
For Schlage Mechanical Locks
- Remove the faceplate from the lock.
- Insert a paper clip into the reset hole located on the inside of the lock.
- Press and hold the reset button for 10 seconds.
- Release the reset button and enter your new code.
- Turn the handle to lock the door.
- Remove the paper clip and replace the faceplate.
People Also Ask About How To Reset Schlage Door Code
How do I reset my Schlage lock without a code?
If you have lost your code or forgotten it, you can reset your Schlage lock using the reset button located on the inside of the lock.
How do I reset my Schlage keypad?
To reset your Schlage keypad, you will need to remove the faceplate from the lock and press the reset button located on the inside of the lock.
How do I set a new code for my Schlage lock?
To set a new code for your Schlage lock, you will need to enter the existing code, followed by the new code, followed by the # key.
